TPP-2 Specifications | |
Mortise and tenon joint Structure (Patented) | Yes |
Hydraulic direct drive full travel cylinders improve 4 times safty rate than the regular chain driving system and reduce the maintence cost by half. | Y |
Two cylinder lifting design provide smooth operation and safety protection | Y |
Multilink structure combine all the paking spaces as a whole reduce the ground requiremnet, improve safety comapre with the single parking space | Y |
3 locking position fasten the operation speed and make manual locking release more comfort to use | Y |
17 locking position provide mechanical protection through all operation height | Y |
Hydraulic safety lock prevent the possible demage may caused by hose burst | Y |
Synchronization chain assure the lifting platform balance also make it possible for the lift to be installed on floor with slight incline. In the unlikely event of structure failure, synchronization chain will work as a safety device to holding failure until it is repaired. | Y |
Anti-slip corrugated deck protect both vehicle and driver from possible slip and deamage but still high-heel shoe friendly | Y |
150% safety reserve on structure strength | Y |
Reduced requirement on floor and base suit different using condition | Y |
Thermal protection save motor from over heating and possible burn with low quality power supply. | Y |
Hydraulic relief valve limits maxmum hydraulic pressure to avoid over capacity of lift | Y |
Air break switch can automatically cut off the electric circuit when occur over load, short circuit, voltage drop. | Y |
Hold to run control button avoided user misoperation | Y |
220V Control provide a easy power connection and reduce maintenance cost | Y |
Lockable master switch only permit authorized operator to be able to use lift | Y |
Upper limit switch postion the height of platform and control the platform highest position | Y |
Car detection photocell 100% protect the ground level car even with misoperation | Y |
Anti toe function with a lower limit sensor to protect operator's toe and foot by stoping platform before it reach floor level then request operator confirm to lower to the ground. | Y |
2.7T capacity for Suvs and cars | Y |
Outdoor version available with galavernization for longer machine life | Y |
Smooth and quiet operation with hydraulic system | Y |
Push up cylinder for longer lift of seal pack | Y |
Telescoping cylinder for lower ceiling height requirement | Y |
Polyurethane hoses for hydraulic make layout easier. | Y |
Fast operation speed takes less waiting time | Y |
Instant double parking space fully use the parking space in a limited place | Y |
Shared column to save precious space for your car | Y |
More space for door opening when parked back in | Y |
Hot-galvanize platfrom guarantee a long lift of the deck even with water or snow affect | Y |
Rain or melt water can only exit from the end of the platform to save your cloth from drop water | Y |
Automatic lock release control during lower down operation make lift can be used by customer with limited experience. | Y |
Extensive information installation manual and video help you install easily | Y |
No lifting chain or pulley need to be maintained | Y |
Project packing with special design for fast installation | Y |
Minimum electrical control for lower installation cost | Y |
Run over ramp for possible trans pass installation | Y |
Grain Seed Palm Almond Walnut Apricot Sheller and Peller and Huller
A level of shelling, roller gap can be adjusted, apricot raw material size is not the same, take off the large adjustment gap and then take off as a cycle ..The roller gap should be 1-1.5mm smaller than the apricot kernel. (If apricot kernel size is mixed together, large apricot kernels have a 15 mm diameter in the flat, 12 mm in the flat, and a small 9 mm in the flat. Adjust according to the raw materials: 14 mm off the first roll gap. The large, large apricot nucleus is removed from the shell and the small apricot kernels are leaked at the same time. The apricot nucleus, which has been removed from the shell, is separated from the apricot kernel that has not been detached from the shell by a sizing screen under the shelling machine. Unopened apricot kernels, from the lower layer of the screen, the apricot kernel almond mixture after opening the shell, and then the second time to remove the roller gap 11mm off the third roll off the gap 8mm off Finished small, once finished. Reference, according to the physical material to adjust the gap to achieve no broken kernel as well,)
Technical Data:
Model |
Productivity (T/H) |
Power (kw) |
Weight (kg) |
Dimension (mm) |
Sieve dimension | Mark |
HLD-300 | 3-5 | 2.5 | 260 | 1900X800X1250 | / | Environment friendly |
Seed Sheller, Almond Sheller, Palm Kernel Sheller, Kernel Shelling Machine
Hebei HELIDA Grain Selecting Machinery Technology Co., Ltd. , http://www.grainseedscleaner.com